DAWSON CZPT & MOULD Group
***EXTRUSION BLOW MOLDING Device Specialist***
Our customers are all about the globe.
Vietnam, Australia, Indonesia, Malaysia, Thailand, Sri Lanka, Kazakhstan, Russia, UAE, Saudi Arabia, Malta, Romania, Italy, India, Syria, Ethiopia, Egypt, Sudan, Tunisia, Algeria, Kenya, Nigeria, South Africa, Zimbabwe, Mexico, Guatemala, Ecuador, Colombia, Venezuela, Peru….
Accumulation type blow molding equipment ABLD100
Suitable for making 100-250L HDPE Lifestyle buoy, floater…
Equiped with MOOG parison controller
with SERVO Motor
Extrusion blow molding equipment ABLD100
| extruder | |||
| 1 | Screw diameter | 100mm | |
| 2 | L/D ratio | 24:1 | |
| three | Screw velocity | 15~50r.p.m. | |
| 4 | Travel motor | 45Kw | |
| 5 | Heating zone with cooling admirer | six zone | |
| six | Output/Potential | a hundred and seventy Kg/hr(HDPE particle) | |
| 8 | Heating capability | 25.1 kw | |
| nine | Vertical adjustment of head | 500mm | |
| 10 | Ahead/Backward adjustment of head | 500mm | |
| 11 | Groove feed barrel cylinder | Have IKV | |
| twelve | Equipment box | Tough gear decelerator | |
| thirteen | Ladder and protection rails | Have | |
| Accumulator CZPT | |||
| one | Accumulator potential | 20L(15kgHDPE) | |
| 2 | Layout | 1st in and initial out | |
| 3 | Heating zone | 6 zone | |
| four | Heating potential | twenty five.1kw | |
| five | Max die&pin diameter | 450mm | |
| 6 | Die head axis with pre-blow | Ø120mm | |
| seven | Accumulator drive-out stroke measurement | Transducer Italy Gefran | |
| 8 | Injection force | twelve Mpa | |
| nine | Extruder cease | Have | |
| CLAMPING Device | |||
| one | Tie bar | Two tie bar | |
| 2 | Platen size | 900(W)X1400(H) | |
| three | Size of mildew | 900-960mm | |
| 4 | Clamping force | 780KN | |
| 5 | Near/Open stroke | 880-1700mm | |
| six | Mould excess weight | Max. 5000 kg | |
| 7 | Clamping stroke measurement | Transducer Italy Gefran | |
| eight | CZPT valve | ZheJiang Hitech | |
| 9 | Number of hydraulic cylinder | 1 | |
| 10 | Higher strain | 14 Mpa | |
| eleven | Assist parts for platen movement | Liner Xihu (West Lake) Dis. | |
| HYDRAULIC Technique | |||
| 1 | Major motor/vice motor | AC15Kw/15Kw | |
| two | CZPT valve | ZheJiang Hitech | |
| 3 | CZPT pump | ZheJiang Hitech | |
| four | Oil tank ability | 850L | |
| 5 | Running force | 12 Mpa | |
| six | Cooling drinking water for oil | set | |
| seven | Manage of oil amount | be noticed dipstick | |
| PNEUMATIC Program | |||
| 1 | Working strain | .eight Mpa | |
| two | Blow force | .8 Mpa | |
| 3 | Needle blow circuit | Higher & lower pressure | |
| four | Intermittent blow | Have | |
| 5 | Managed assist air for parison | Have | |
| six | Air Valves | AIRTAC | |
| 7 | Swift exhaust for support air | Have | |
| PARISON Manage | |||
| one | Programmer | JAPAN MOOG | |
| 2 | Servo valve | MOOG |
|
| 3 | Servo cylinder | Intergret of die head | |
| four | CZPT pack |
ZheJiang YOSHE Variable Displacement Piston Pumps |
|
| CZPTITY | |||
| 1 | Contactor |
Schneider |
|
| 2 | Complete connected load (approx.) |
114kw/h | |
| three | Regular energy use (approx.) |
42 kw/h | |
| Water COOLING | |||
| one | Equipment drinking water usage |
6000L/h | |
| two | Mould water consumption |
6000L/h | |
| AIR Intake | |||
| 1 | Compressed air intake | one.two kgf/cm2, 3000 L/min | |
| OTHER Functions | |||
| one | PLC management | MITSUBISHI | |
| two | Xihu (West Lake) Dis.n device interface | Hitech | |
| three | Recipe storage in challenging disk | Accessible | |
| HEATING Handle | |||
| 1 | Electrical power provide to heating aspect | Relay + Contactor | Japan Omron+Korea LG |
| 2 | Handle | PLC controle | |
| three | Kind of thermocouple | K Type | |
| four | Adjustable reduce and higher limit alarm | Have | |
| five | Cold commence prevention for screw | Have | |
| 6 | Alarm for thermocouple and heating component breakage | Have, heating aspect breakage by anperemeter | |
| seven | Pre-heating purpose | Have | |
| Die-ring AND Die-pin | |||
| 1 | 1 sets of die & pin | One particular set according to client | |
| two | Test material | Buyer provide 300kg materials to seller for equipment tests | |
| Choice | |||
| one | Base blow (hydraulic) and sealing unit (pneumatic) | CZPT blow pin (such as grow & up-down & parison seal) | |
| 2 | Robot | Have | |
| 3 | Equipment Dimension | 6.8×3.3×5 | |
| 4 | Total excess weight | twenty | |
